West Coast Wrench logo West Coast Wrench — Appliance Installation & Repair
Installation By West Coast Wrench Technical Team November 15, 2026 5 min read

Installing a New Refrigerator: A Homeowner’s Checklist

A new fridge should be a simple swap, but a surprising number of problems start on delivery day: doors that cannot open fully, an ice maker line that drips behind the cabinet, or a fridge that hums loudly because it is boxed in. Work through this checklist and the new one will start life properly.

⚠ Water Behind or Under the Fridge?

Turn off the water supply to the fridge, unplug it if water is near the outlet, and dry the area. A slow drip from a water line can damage floors and the unit below in a condo. Call West Coast Wrench at (236) 330-7180 (Mon–Sun 8:00am–10:30pm) or send us a service request.

Diagram of airflow around refrigerator condenser coils
A fridge needs space to move warm air away from its condenser. Airflow Clearance

Quick Answer

Measure the opening and the path into the kitchen, and leave the air gap the manual asks for. Plan for doors to open far enough to pull out the crisper drawers. Use a proper shut-off valve and a braided or copper line for the ice maker, never a self-piercing saddle valve. Level the fridge so the doors swing closed, flush the water filter, and allow time for it to cool before loading food.

Before Delivery: Measure Three Things

The opening. Measure width, height and depth at several points; old cabinets and floors are rarely square. Then check the manual for the air gap the fridge needs at the sides, top and back. Squeezing a fridge into a space with no gap makes the compressor work harder and can make it noisy.

The doors. A fridge beside a wall may not open far enough to pull the crisper drawers out. French-door and bottom-freezer models are especially fussy. Check the door-swing measurement in the specifications.

The route. Measure front doors, hallways, tight corners and stairs. Many fridges need their doors removed to get through older Victoria doorways, which is worth knowing before the truck arrives.

The Water Line Is Where Most Leaks Start

If your new fridge has an ice maker or water dispenser, the supply line matters more than anything else on this list.

  • Use a proper quarter-turn shut-off valve, not a self-piercing saddle valve. Saddle valves are a common source of slow leaks.
  • Use a braided stainless or copper supply line long enough to let the fridge be pulled out for cleaning, with a loop behind it rather than a tight bend.
  • Check the connection at the fridge and at the valve for drips after the first fill, and again the next day.
  • In a condo, check your strata rules; some buildings have requirements for water lines and leak trays.

When to Call a Professional

  • There is no water shut-off near the fridge or the old valve will not turn.
  • The line has to run through a cabinet, wall or floor.
  • The fridge is noisy, warm or leaking after installation.
  • Doors will not seal or swing closed even after levelling.

A careful installation now prevents the slow leaks and door problems that cause expensive damage later.

Setting It Up

  1. Let it stand if needed. If the fridge was carried on its side, follow the manufacturer’s guidance on waiting before you plug it in.
  2. Plug it straight into a wall outlet. No extension cords or power bars.
  3. Level it with a slight tilt back. Most fridges are designed so the doors swing closed on their own; the manual explains how to adjust the front feet or rollers.
  4. Flush the water filter. Run water through the dispenser as the manual directs to clear air and carbon fines, and throw away the first few batches of ice.
  5. Give it time. A new fridge can take many hours to reach temperature. Load food once it is properly cold.

Condos, Townhomes and Older Houses

In a condo, book the service elevator for delivery day if your building requires it, and protect the hallway and unit floors before the old fridge is wheeled out. Find the water shut-off for the fridge line before installation, not after a leak; in many units it sits under the kitchen sink or in a cabinet next to the fridge. A leak tray under the fridge is a cheap extra layer of protection where a drip could reach the suite below.

In older Victoria houses, check that the fridge outlet is not shared with a microwave or kettle on the same circuit, and that the floor under the fridge is solid enough to level it properly. If the doors will need to hinge on the other side, many models can be reversed, but it is far easier to do before the fridge is pushed into place.

After Installation: Normal and Not Normal

New fridges make sounds that older ones did not: clicks from the ice maker, gurgling as refrigerant moves, and a soft hum from variable-speed compressors. Those are normal. Water pooling inside, frost building up on the back wall, or a fridge that never stops running are not. Our guides to a fridge that runs constantly and testing the door seal can help you tell the difference.

If you would rather have it done for you, our professional appliance installation in Greater Victoria includes the water line, levelling and a leak check. If the new fridge is not cooling properly once installed, book refrigerator repair in Greater Victoria and we will find out why.

Frequently Asked Questions

How much space does a refrigerator need around it?

It depends on the model, so check the installation guide. Most fridges need a small air gap at the top, sides and back so warm air can escape from the condenser.

Should I use a saddle valve for my fridge water line?

No. Self-piercing saddle valves are a common source of slow leaks. Use a proper quarter-turn shut-off valve and a braided stainless or copper supply line.

How long before I can put food in a new fridge?

Wait until it reaches its set temperature, which can take many hours. Check with a fridge thermometer before loading perishables.

Why won’t my new fridge doors close by themselves?

The fridge is probably not levelled with the slight backward tilt it is designed for. Adjust the front feet or rollers as the manual describes.

Greater Victoria Appliance Service

Ready to Book a Diagnostic Visit?

A technician comes to your home and finds the fault first. The diagnostic visit fee depends on your municipality, and you get an upfront flat-rate quote before any repair starts. If you decide not to go ahead, the diagnostic visit is the only charge. We answer Monday to Sunday, 8:00am to 10:30pm.

Call (236) 330-7180 Contact Us or Request Service
Clear, Honest Process

How Our Service Visits Work Across Greater Victoria

We believe in straightforward service with zero guesswork. Before any repair begins, you know exactly what failed and what it costs to fix.

Confirmed Arrival Window & Courtesy Call

Speak directly with our Victoria dispatch team seven days a week (8:00 am – 10:30 pm). We schedule a convenient window and call or text when your technician is on the way.

In-Home Diagnostic ($110 – $160 CAD)

A technician backed by $2M Commercial General Liability insurance and our CRD Intermunicipal Business Licence tests your appliance on-site (standard diagnostic visit is $110–$160 depending on municipality across all 13 Greater Victoria municipalities) and explains the exact issue in plain English.

Upfront Flat-Rate Quote Before Work Begins

You receive a clear flat-rate price for the repair before we turn a wrench. You approve the exact cost first — no hourly billing surprises and no hidden fees.

Fast Response • 8:00 am – 10:30 pm Daily

Request a Quick Callback or Quote

Leave three quick details and our dispatch team will call you back promptly, or call us directly right now.

Prefer to speak with us right now? Call (236) 330-7180
Call (236) 330-7180 Request Callback